FixtureBathPriced by fixture count and finish level, the way a contractor bids it.

Cost to move a vanity 3 to 6 ft on a concrete slab

Moving a vanity or basin 3 to 6 ft on a concrete slab
$450 – $1,750
about $1,100 typical · this is the ADDER, on top of the fixture and the finishes
Cost to move it$450 – $1,750
Same move on a wood floor, short distancethe cheapest version of this move, for comparison$150 – $550
Fixturesupply lines and a 1½″ drain — the cheapest thing to movea vanity or basin
Floorcut, break out, re-plumb, backfill and re-pour — a different trade on topa concrete slab
Distancelikely crosses a joist — headers or a re-route3 to 6 ft
Multiplier against the base2.2×

Notes

  • This is an adder, not a price for the work. It is what moving the fixture costs on top of the fixture itself, the tiling, the waterproofing and the finishes. A layout change that moves three fixtures stacks three of these.
  • Moving a vanity or basin is one of the cheaper changes, because the drain is small and the slope requirement is easier to satisfy over a short run. If the layout has to change, moving this rather than the toilet is where the money is.
  • A concrete slab roughly doubles it, and it is a second trade. The floor has to be cut, broken out, the pipe re-run, backfilled, and re-poured — then the new concrete has to cure before tiling. That is days of programme as well as money, and on a post-tension slab it may not be permitted at all without an engineer locating the cables first.
  • At 3 to 6 ft the run usually stays simple, which is why this is the version of the change worth designing toward.
  • Keeping the layout is the single biggest saving in a bathroom remodel. New fixtures in the existing positions, with new tile and a new vanity, produces most of the visible change for a fraction of the plumbing cost. It is worth pricing both versions before falling in love with a drawing.
  • Ask what happens if the existing drain is cast iron. Older houses often are, and cutting into it means transition couplings and frequently discovering the rest of the line is worse than expected. That is the most common mid-job surprise on this work.

$450 – $1,750 — and it is an adder, not the job

That is what moving a vanity costs on top of the fixture, the tile, the waterproofing and the finishes. A layout change that moves three fixtures stacks three of these.

Why the toilet is the expensive one

A basin needs a 1½ inch drain that can run almost anywhere. A toilet needs a 3 inch drain holding ¼ inch of fall per foot, plus a vent.

Every foot further from the stack drops the pipe another quarter inch. Ten feet of travel is 2½ inches of drop, and it has to fit between the top of the floor and whatever is below.

That is the point where "we can move it, it just costs more" becomes "not in that corner". Slope is a hard constraint, not a budget one.

The floor decides the multiplier

A joist floor means the plumber works in the joist bay, and how easy that is depends on access from below. An unfinished basement underneath and the bathroom floor barely gets touched.

A concrete slab means cutting, breaking out, re-plumbing, backfilling and re-pouring — a second trade, days of programme, and the new concrete has to cure before anything is tiled. On a post-tension slab it may not be permitted at all until an engineer has located the cables.

The saving nobody wants to hear

Keeping the existing layout is the single largest saving available in a bathroom remodel. New fixtures in the same positions, with new tile and a new vanity, delivers most of the visible change for a fraction of the plumbing cost.

Price both versions before committing to a drawing.

Ask what happens if the drain is cast iron

Older houses often are. Cutting into cast iron means transition couplings, and it frequently means discovering the rest of the line is in worse condition than anyone assumed. It is the most common mid-job surprise on this work, and it is worth asking about before demolition rather than during it.

Nearby sizes

Read more